How to Upload a Cobb Accessport Map

Special Notes Nearly Your AccessPORT Install:

• Install the AP Manager Program and Check for updates. This is the commencement most important stride to brand sure your AP has the near upward to appointment ECU, Vehicle information and MAPs for your car. Subsequently the update, y'all will not see the maps in the AP manager until the AccessPORT is installed on your car. The PERRIN Custom Map is not going to be seen until you load the custom map we email you.
• Make sure your central is in the on position.  The AccessPORT will not install and say "Tin can't Connect To Vehicle, Reconnect Cablevision and Try Again" unless the key is in the on position.   The simplest style to check this is to make certain you can see your gas gauge. If you can run into this, you should be able to install the AccessPORT onto your car. 02-07 WRX/STI's need to make sure their Green Test Connectors are connected as well, or AP will not install.

Step ane. Download and Install AccessPORT Director

The AP Manager programme is a tool that not only updates your AP, but besides information technology allows y'all to manage all your maps/logs and ECU data for your AccessPORT.  This is the start most important step to make sure your AP has the most upwards to engagement ECU and Vehicle data.  Making sure its updated earlier your install is the best fashion to ensure you have a successful AccessPORT installation.   Install this program using the below links depending on your computers operating system.

Step ii. Update Your AccessPORT:

Update your AccessPORT Earlier you load maps or attempt to install to vehicle.  This ensures you have the about electric current mapping and functionality for your AccessPORT.

• With the AP Manager program installed, make sure your computer is connected to the internet and plug in your AccessPORT to your estimator.
• Let the AccessPORT to be plugged in for roughly thirty seconds to allow new drivers to be installed.
• Open the AP Manager program and make sure it connects to the AccessPORT itself.  If it doesn't do this automatically, click on the "Connect" button on the upper correct side.
• Click on the "Updates" push button.  If there is an update available, click on "Begin Firmware Update"  and let the AccessPORT complete the update, which takes roughly v minutes to complete.  Its completed when you meet the message "Your AccessPORT is Upwardly To Appointment".

Stride 3. Install the AccessPORT to your car:

• Locate the OBD port on your vehicle and plug the AccessPORT OBD cablevision into it.  This is located under the dash on the drivers side of vehicle.  Plug OBD cablevision into rectangle connector on AccessPORT. Pictured below is an older fashion OBD cablevision used on AccessPORT's.  These OBD cables consisted of a "Dongle" (grey OBD connector) and a hinge style USB cable. These still get plugged into the OBD port but the smaller end of the USB gets pluged into the back of the dongle, and the other end of the USB gets plugged into the AccessPORT.

• For all 2008+ cars (with Can Charabanc ECU's) Place key into the ignition and turn to the ON position (do not start engine).  A expert indicator that the car is on, is to look at the gas gauge. If the gas judge is illuminated then the fundamental is in the "On" position.  Sounds like a unproblematic matter to exercise, simply ninety% of the time a customer calls considering the AccessPORT doesn't work, its because the central wasn't in the "ON" position.  Make sure that the radio, lights, Heater/Ac controls and all accessories are turned off and battery is fully charged before flashing ECU.
• For all 2002-2007 WRX/ STI's, located green test connectors nether dash and connect them. These are unremarkably subconscious up inside of nuance on drivers side of motorcar, directly above the hood latch.    Once continued identify key into the ignition and plough to the ON position (do not outset engine).  Make sure that the radio, lights, Heater/Ac controls and all accessories are turned off and bombardment is fully charged before flashing ECU.

• Press the "Enter" button when your AccessPORT shows the "Install" screen.  Verify your machine matches the described vehicle on the screen.  SPECIAL Note: If the AccessPORT doesn't recognize your auto, please follow the instructions in the "Relieve My ECU Information" beneath.
• Follow the on screen directions until y'all are asked to option what map to install.  Choice the custom PERRIN map nosotros emailed to you. Clicking on the map one time, will show a larger clarification for the map., which will help decide if this is the right map.If you have questions nigh this, or haven't seen your map, give united states a phone call so we tin assist you ASAP.
• The AccessPORT will showtime save your ECU data, then it volition keep with flashing the custom map onto the ECU.

• When the AccessPORT is done installing your custom map, turn fundamental to the off position, disconnect the AccessPORT from the OBD port. (02-07 WRX/STI's need to disconnect greenish test connectors)
• Turn key to the on position, and wait for five seconds for the ECU to reboot.  Then beginning the car and savor the new found power!

If Vehicle Is Not Recognized.......

Every bit new cars are released It may be necessary to dump the vehicle information stored in your AccessPORT.  This procedure takes well-nigh 10minutes to complete and after we get the ECU information, information technology tin can accept a few days to go the AccessPORT updated.  Please be patient as this procedure involves Cobb to add teh vehicle to the ECU database and sometimes create new maps and tuning software. This is a very rare occasion that this will demand to be washed. This typically but happens with brand new cars for new model years.

• During the installation procedure, yous may see the screen "Failed to Recognize Vehicle.........."
• If this comes up, hit the OK button and go on to the USER TOOLS section.

• Click on the" Salve ECU Data" button and follow the on-screen instructions to save ECU data.
• When the AccessPORT is done saving data, it will return to the install screen.  Its now ok to unplug AccessPORT from car.
• Open AccessPORT Manager software and plug in your AccessPORT and click the Connect button.
• Click on Filter drop down bill of fare to show "All files".  Locate your ECU data file and highlight it.

• Click on  "Relieve Selected Files to Computer" button, or drag the file to y'all desktop.
• Etch and electronic mail containing your name, your car, transmission and build date.  Send an email with the file fastened to [email protected]
• We will pass this info along to Cobb Tuning and try to provide you with an estimated date to get your AP working.
• Once Cobb adds your vehicle to the database, yous will need to update your AP using the "Bank check For Beta Firmware", under the Options bill of fare.

• After the update is complete, go out to your car and install your AccessPORT post-obit the instructions on how to install the AP.

Whatsoever questions regarding AccessPORTs and the installation?  Send an email or live chat with us!

[email protected]

503-693-1702

slaterdialletrem.blogspot.com

Source: https://www.perrin.com/blog/post/how-to-install-your-accessport-subaru

Share this post